[May-2025] The Best AMPP-SICT Study Guide for the Senior-Internal-Corrosion-Technologist Exam
Senior-Internal-Corrosion-Technologist certification guide Q&A from Training Expert Pass4Leader
NEW QUESTION # 18
When observing design defects the NACE Inspector should:
- A. Stop the job immediately
- B. Document the defect and the potential problems that could result
- C. Request that the item be rebuilt with a better design for coating
- D. Ignore the defect as the inspector can't change the design
Answer: B
NEW QUESTION # 19
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Non-Conductive coatings applied to a conductive metallic substrate
- B. Conductive coatings applied to a magnetic metallic substrate
- C. Conductive coatings applied to a cementitious substrate
- D. Magnetic coatings applied to a magnetic metallic substrate
Answer: C
NEW QUESTION # 20
Thermal Spray coatings provide:
- A. Barrier protection
- B. Sacrificial protection
- C. inhibitiveprotection
- D. Thermal protection
Answer: A
NEW QUESTION # 21
Coating Surveys are legally required:
- A. On food and beverage vessels and can linings
- B. On high pressure gas lines and fireproofed structures
- C. On water tanks and potable water pipelines
- D. On commercial marine vessels and offshore platforms
Answer: D
NEW QUESTION # 22
On pipelines, which coating is Identifiable by Its distinct colors, usually light blue, green, or grey?
- A. Heat-shrink sleeves
- B. Coal Tar Enamel
- C. Concrete
- D. Liquid epoxies
Answer: D
NEW QUESTION # 23
Which product, when closely inspected has a green or ted layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. 3-Layer Polyethylene (PE)
- C. Fusion Bonded Epoxy
- D. 2-Layer Polyethylene (PE)
Answer: C
NEW QUESTION # 24
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed.
The specification references SSPC SP 16 as the surface preparation method. At the pre-Job meeting operations personnel make it dear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used. Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by SP 2
- B. SP 1 followed by SP 3
- C. SP 1 followed by caustic etching
- D. SP 1 followed by acid etching
Answer: D
NEW QUESTION # 25
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. Explosion resistance
- C. Fire extinguishing characteristics
- D. Preferential fuel for the file
Answer: A
NEW QUESTION # 26
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide If and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION # 27
The most likely area of failure on a buried external pipeline coating is the:
- A. Mainline coating
- B. Areas exposed to Ultra Violet light
- C. Ground bed
- D. Field Joint coating
Answer: D
NEW QUESTION # 28
Non-Conformance Reports are designed to:
- A. Punish the Contractor for substandard work
- B. Elevate the status of the Inspector
- C. To Identify items that do not meet the specification requirements
- D. Assist the Owner in negotiating credits from the Contractor
Answer: C
NEW QUESTION # 29
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals Is:
- A. Cost
- B. Safety
- C. Iron content
- D. Appearance
Answer: C
NEW QUESTION # 30
A reinforced coating is
- A. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. equally resistant to abrasion and impact as a non-reinforced coating.
- D. equally resistant to movement and impact as a non-reinforced coating.
Answer: A
NEW QUESTION # 31
Coating application to concrete substrates is:
- A. The same as coating steel
- B. More challenging than coating steel
- C. Less challenging than coating steel
- D. Not required as concrete is Inorganic
Answer: B
NEW QUESTION # 32
NACE No. 13/ SSPC 6 Identifies the use of:
- A. Abrasive blasting only
- B. Various methods of cleaning
- C. Watterjetting only
- D. Steam cleaning only
Answer: B
NEW QUESTION # 33
You have Just received your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to determine the scope of your role
- B. Advise the prospective employer that you cannot accept the position
- C. Review the NACE Attestation prior to making a decision
- D. Accept the assignment without hesitation
Answer: A
NEW QUESTION # 34
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. The same as air blast cleaning
- B. Different than air blast cleaning
- C. Comparable to air blast cleaning
- D. Slightly different to air blast cleaning
Answer: A
NEW QUESTION # 35
......
The Best AMPP Senior-Internal-Corrosion-Technologist Study Guides and Dumps of 2025: https://www.pass4leader.com/AMPP/Senior-Internal-Corrosion-Technologist-exam.html
Senior-Internal-Corrosion-Technologist Certification Overview Latest Senior-Internal-Corrosion-Technologist PDF Dumps: https://drive.google.com/open?id=1ZM4hMER8GqygnNiRPl408epki1OgAiX5