Free Dell DSDSC-200 Practice Test & Real Exam Questions

Exam Code/Number: DSDSC-200
Exam Name/Title: Dell SC Series Storage Professional Exam
Certification Provider: Dell
Corresponding Certification: Dell Certification

Exam Questions: 120
Updated On: Oct 06, 2026

Question #1

During failover testing, an engineer finds that the iSCSI connection failed over properly when a physical link was disconnected. The FC connection did NOT failover when a physical link was disconnected.
Which configuration is causing this issue?

A. iSCSI is in legacy port mode, and FC is in legacy port mode.

B. iSCSI is in virtual port mode, and FC is in legacy port mode.

C. iSCSI is in legacy port mode, andFC is in virtual port mode.

D. iSCSI is in virtual port mode, and FC is in virtual port mode.

Discussion 0

Correct Answer: C Vote an answer

Question #2

An administrator has multiple servers that need to be connected to the Storage Center through two iSCSI networks.
The engineer uses a software iSCSI initiator on the servers.
The Storage Center runs in Virtual Port mode.
What item(s) must the administrator know to connect the hosts to the? Storage Center?

A. Control port IP addresses

B. Virtual port IP addresses

C. Management IP address

D. iSCSI Initiator Name

Discussion 0

Correct Answer: A Vote an answer

Question #3

A Storage Administrator wants to do a Storage Center OS update to SCOS version 6.7.5.
The Storage Center is currently at SCOS version 6.5.30.
The Storage Center is at a secure facility and does NOT allow connectivity to any network outside the facility.
The Storage
Administrator is trying to use the Storage Center Update Utility to accomplish this task, but has been unsuccessful in doing so.
Why has the Storage Administrator been unsuccessful?

A. The Storage Center isNOTat the minimum required SCOS version to use the utility.

B. The Storage Center hasNOTpassed Pre-Upgrade checks and is blocking the update from occurring.

C. The Storage Center isNOTlicensed to use the Storage Center Update Utility.

D. The secure facility is NOTallowing the StorageAdministrator's laptop to connect to the Storage Center across the network.

Discussion 0

Correct Answer: A Vote an answer

Question #4

An engineer has installed an SC4020 with four FC ports in each controller.
This is a dual- fabric installation with four FC connections in each server.
The servers use the OS built-in multi-pathing capabilities.
Which two configurations will cause the controller failover to fail? (Choose two.)

A. The multi-pathing software is incorrectly configured.

B. Too many volumes are mapped to the server from one controller.

C. The switch zoning is incorrectly configured.

D. The server HBA timeouts are set incorrectly.

Discussion 0

Correct Answer: A,C Vote an answer

Question #5

The deployment engineer runs all of the commands to initialize the system and reboot the controller.
The engineer then tries to log in several times as tunes asAdmin/mmm before the setup wizard runs.
This login fails.
Why is the user Admin/mmm unable to log in?

A. The account has been locked because the user tried to type the password multiple tunes before die system was fully initialized

B. The user changed the password for Admin during the initialization process.

C. The default password for the Admin account is P@ssword 1.

D. The first login must be done with the user "shellaccess" and the password "developer".

Discussion 0

Correct Answer: A Vote an answer

Question #6

The engineer notices that iSCSI servers are NOT performing as expected. After reviewing the graphics, the engineer identifies high latency due to an excessive number of retransmits. What is causing the performance issue?

A. A VLAN ID value is set on the properties of the server NT

B. Switch firmware is out of date.

C. Flow Control is disabled.

D. The system uses the standard MTU size.

Discussion 0

Correct Answer: A Vote an answer

Question #7

Which method should be used to map a volume to a server in Enterprise Manager?

A. In the Storage Viewer: during the Volume Create wizard, click the "Mapping Options" link, and choose the server to map to.

B. In the Server Viewer: highlight the server on the list andclick the "Map Volume to Server" button on the top button bar.

C. In the Storage Viewer: highlight an unmapped volume and click the "Map Volume to
Server" button on the top button bar.

D. In the Reporting Viewer: open the mapping report, click "CreateNew Mapping", and provide the requested information.

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Download Free Dell DSDSC-200 Demo

Simply submit your e-mail address below to get started with our free demo of your Dell DSDSC-200 exam.