Free Network Appliance NS0-502 Practice Test & Real Exam Questions

Exam Code/Number: NS0-502
Exam Name/Title: NetApp Certified Implementation Engineer - SAN, 7-Mode
Certification Provider: Network Appliance
Corresponding Certification: Network-Appliance NAC-NIE Certification

Exam Questions: 106
Updated On: Sep 13, 2026

Question #1

After completing the configuration of a new Brocade Fibre Channel switch, which command do you use to verify your configuration?

A. cfgshow

B. switchshow

C. show config

D. configshow

Discussion 0

Correct Answer: D Vote an answer

Question #2

Which task is part of the site preparation for installation?

A. install equipment in rack

B. configure zoning

C. verify equipment move path

D. verify host to storage connectivity

Discussion 0

Correct Answer: C Vote an answer

Question #3

What are two possible impacts to consider when changing the cfmode to single_image?. (Choose two.)

A. Target port WWPNs will change on at least one controller.

B. You must use hard zoning (zoning by ports).

C. hosts running Solaris since it does not support single_image cfmode

D. There more paths to LUNs.

E. There are fewer paths to LUNs.

Discussion 0

Correct Answer: A,D Vote an answer

Question #4

When booting your NetApp storage system for the first time the system fails to boot.
What should you do first to address this problem?

A. You turn off your storage system and disk shelves, and then turn on the disk shelves. You then check the quick reference card that came with the disk shelf for information about LED responses.

B. You verify disk shelf compatibility and check the disk shelf IDs to verify that the disk shelf 1 (for DS14 series) must be connected to your system.

C. You re-download the boot image to the compact flash card, then reboot the system.

D. You look for a description of the problem on the LCD and console. You then follow the instructions, if provided, on the LCD and console.

Discussion 0

Correct Answer: D Vote an answer

Question #5

Click the Exhibit button.

In the diagram shown, a portset is created on controller 1 with the command: controller1>portset create -f
ntapportset conroller1:0b. This portset is bound to the igroup with all the intiators in it. How many paths can the host 1 see to a LUN on controller 1?

A. one path

B. four paths

C. six paths

D. three paths

Discussion 0

Correct Answer: A Vote an answer

Question #6

Which statement is correct regarding virtual machine alignment on VMware ESX?

A. Alignment issues can occur on any protocol including FCP, iSCSI, FCoE, and NFS

B. RDM LUNs do NOT suffer from alignment problems because they are accessed directly by VMs.

C. A VMFS LUN with a LUN type of VMware, will always have properly aligned VMs.

D. msinfo32 or mbrscan can be run for the ESX service console to check for proper alignment of VMs.

Discussion 0

Correct Answer: A Vote an answer

Question #7

NetApp supports multiple FC paths from the host to the NetApp storage controllers. In addition to using multiple FC switches, which other NetApp supported components should you use for this type of configuration?

A. HBA with driver and firmware, multiple storage controllers with multiple target ports each

B. HBA with driver and firmware, multipathing host software, multiple storage controllers with multiple initiator ports each

C. HBA with driver and firmware, multipathing host software, multiple storage controllers with multiple target ports each

D. multipathing host software, multiple storage controllers with multiple target ports each

Discussion 0

Correct Answer: C Vote an answer

Question #8

When does Fractional Reservation reserve space from the volume?

A. LUN Creation

B. LUN SnapMirror

C. Volume Creation

D. Volume Snapshot

Discussion 0

Correct Answer: D Vote an answer

Question #9

An organization currently has a NetApp Fibre Channel block-based solution. With limited budget and resources, they want to create a new disaster recovery site that utilizes a NetApp solution. What would the optimal solution include?

A. SnapMover and Fibre Channel at the disaster recovery site for all hosts

B. MetroCluster and NAS

C. Fibre Channel at both locations using ftp to replicate storage

D. SnapMirror and iSCSI at the disaster recovery site for all hosts

Discussion 0

Correct Answer: D Vote an answer

Question #10

In a NetApp SAN solution, which value should you set for snap reserve for a volume holding LUNs?

A. 0%

B. 20%

C. 100%

D. 50%

Discussion 0

Correct Answer: A Vote an answer

Download Free Network Appliance NS0-502 Demo

Simply submit your e-mail address below to get started with our free demo of your Network Appliance NS0-502 exam.