Free Fortinet NSE8_813 Practice Test & Real Exam Questions

There is an interface-mode IPsec tunnel configured between FortiGate1 and FortiGate2.
You want to run OSPF over the IPsec tunnel. On both FortiGates. the IPsec tunnel is based on physical interface Port1. Port1 has the default MTU setting on both FortiGate units.
Which statement is true about this scenario?

Refer to the exhibit. You are operation an internal network with multiple OSPF routers on the same LAN segment. FGT_3 needs to be added to the OSPF network and has the configuration shown in the exhibit. FGT_3 is not establishing any OSPF connection.
What needs to be changed to the configuration to make sure FGT_3 will establish OSPF neighbors without affecting the DR/BDR election?

You are asked to write a FortiAnalyzer report that lists the session that has consumed the most bandwidth. You are required to include the source IP, destination IP, application, application category, hostname, and total bandwidth consumed.
Which dataset meets these requirements?

The wireless controller diagnostic output is shown on the exhibit.
Which three statements are true? (Choose three.)

You have replaced an explicit proxy Web filter with a FortiGate.
The human resources department requires that all URLs be logged. Users are reporting that their browsers are now indicating certificate errors as shown in the exhibit.
Which step is a valid solution to the problem?

You have configured a Site-to-Site IPsec VPN tunnel between a FortiGate and a third-party device but notice that one of the error counters on the tunnel interface keeps increasing.

Which two configuration options can resolve this problem? (Choose two.)

Refer to the exhibit.

An organization has a FortiGate cluster that is connected to two independent ISPs. You must configure the FortiGate failover for a single ISP failure to occur without disruption.
Referring to the exhibit, which two FortiGate BGP features are enabled to accomplish this task?
(Choose two.)

Refer to the exhibit.

An HTTPS access proxy is configured to demonstrate its function as a reverse proxy on behalf of the web server it is protecting. It verifies user identity, device identity, and trust context, before granting access to the protected source. It is assumed that the FortiGate EMS fabric connector has already been successfully connected.
You need to ensure that ZTNA access through the FortiGate will redirect users to the FortiAuthenticator to perform username/password and multifactor authentication to validate access prior to accessing resources behind the FortiGate.
In this scenario, which two further steps need to be taken on the FortiGate? (Choose two.)

What is the benefit of using FortiGate NAC LAN Segments?

Refer to the exhibit.

A customer needs to create a multi-tier MCLAG set up with the topology as shown in the exhibit.
A1/A2
B1/B2
C1/C2
Which command snippet should be applied to it, to allow active/active links in this topology?

A company has just rolled out new remote sites and now you need to deploy a single firewall policy to all of these sites to allow Internet access using FortiManager. For this particular firewall policy, the source address object is called LAN, but its value will change according to the site the policy is being installed.
Which statement about creating the object LAN is correct?

You want to access the JSON API on FortiManager to retrieve information on an object.
In this scenario, which two methods will satisfy the requirement? (Choose two.)

You are asked to implement a single FortiGate 5000 chassis using Session-aware Load Balance Cluster (SLBC) with Active-Passive FortiControllers. Both FortiControllers have the configuration shown below, with the rest of the configuration set to the default values.

Both FortiControllers show Master status.
What is the problem in this scenario?

Your company uses a cluster of two FortiGate 3600C units in active-passive mode to protect the corporate network. The FortiGate cluster sends its logs to a FortiAnalyzer and you have configured scheduled weekly reports for the Internet bandwidth usage of each corporate VLAN.
During a scheduled maintenance window, you make a series of configuration changes.
When the next FortiAnalyzer weekly report is generated, you notice that Internet bandwidth usage reported by the FortiAnalyzer is far less than expected.
What is the reason for this discrepancy?

Which two methods are supported for importing user defined Lookup Table Data into the FortiSIEM? (Choose two.)