Free EMC D-PDC-DY-23 Practice Test & Real Exam Questions

Exam Code/Number: D-PDC-DY-23
Exam Name/Title: Dell PowerSwitch Data Center Deploy 2023
Certification Provider: EMC
Corresponding Certification: Dell Networking

Exam Questions: 205
Updated On: Aug 07, 2026

Question #1

Which commands are required to properly configure an OS10 switch to run OSPF on eth1/1/3 and to add network 144.254.1.0/30 to OSPF area 0?

A. OS10(config)# interface ethernet 1/1/3
OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30
OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0
OS10(config)# router ospf 1

B. OS10(config)# interface ethernet 1/1/3
OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30
OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0
OS10(conf-if-eth1/1/3)# router ospf 1

C. OS10(config)# interface ethernet 1/1/3
OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0
OS10(config)# router ospf1

D. OS10(config)# router ospf 1
OS10(config-router-ospf-1)# router-id 1.1.1.1
OS10(config)# interface ethernet 1/1/3
OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0

Discussion 0

Correct Answer: C Vote an answer

Question #2

There is a spanning tree mismatch at the global level. PVST+ is configured on a VLT peer. All VLT port channels go down on both VLT peers. A syslog error message is generated.
What is the correct action to resolve the issue?

A. Perform a mismatch check after the VLT peer is established.

B. Use the show VLT detail and show VLT brief commands to view the VLT port channel status information.

C. Verify the VLT LAG ID is configured correctly on both VLT peers.

D. Enable RSTP on both VLT peers.

Discussion 0

Correct Answer: D Vote an answer

Question #3

Which user role in OS10 has full access to all commands and exclusive access to commands that manipulate the file system?

A. secadmin

B. netadmin

C. netoperator

D. sysadmin

Discussion 0

Correct Answer: D Vote an answer

Question #4

The destination O E2 144.254.32.0/24 appears in the routing table of a switch.
What is true for this route?

A. The network represents an OSPF inter-area route

B. The route has been redirected from eBGP

C. It is a non-native OSPF route

D. There are two (2) egress paths with equal costs to the destination

Discussion 0

Correct Answer: C Vote an answer

Question #5

Which OSPF router is responsible for originating Network Link State Advertisements?

A. Internal Router

B. Backbone Router

C. Designated Router

D. Area Border Router

Discussion 0

Correct Answer: C Vote an answer

Question #6

Two Dell Networking OS10 switches in a VLT configuration must be upgraded.
How will the reload of these switches proceed to result in the default initial state?

A. Reload the primary VLT node.
This process will automatically trigger the reload of the secondary node after it has recovered.

B. Reload the primary VLT node.
This will automatically trigger the simultaneous reload of the secondary node.

C. Reload the primary VLT node and wait for it to join as primary.
Wait until after delay restore timer has expired.
Reload VLT secondary node and wait for it to join as secondary.

D. Reload the primary VLT node and wait for it to join as secondary.
Wait until after delay restore timer has expired.
Reload VLT secondary node and wait for it to join as secondary.

Discussion 0

Correct Answer: D Vote an answer

Question #7

Refer to the exhibit.

The output shown is from which command?

A. S3(config-router-ospf-1)# show ip ospf topology

B. S3(config-router-ospf-1)# show ip ospf database

C. S3(config-router-ospf-1)# show ip ospf statistics

D. S3(config-router-ospf-1)# show ip ospf lsa

Discussion 0

Correct Answer: B Vote an answer

Question #8

How does a DHCP Client make a request to a DHCP server following an offer?

A. Multicast

B. ACK

C. Unicast

D. Broadcast

Discussion 0

Correct Answer: D Vote an answer

Question #9

Which command mode allows configuration of switches L2 and L3 interfaces?

A. EXEC Mode

B. Interface

C. Global

D. Configuration

Discussion 0

Correct Answer: B Vote an answer

Question #10

What is a valid RADIUS Authentication command?

A. OS10(config)# radius-server timeout 1500

B. OS10(config)# radius-server retransmit 10

C. OS10(config)# radius-server timeout never

D. OS10(config)# radius-server retransmit 150

Discussion 0

Correct Answer: B Vote an answer

Download Free EMC D-PDC-DY-23 Demo

Simply submit your e-mail address below to get started with our free demo of your EMC D-PDC-DY-23 exam.