Free Cisco 300-415 Practice Test & Real Exam Questions, Page 1

Question #1

An enterprise is continuously adding new sites to its Cisco SD-WAN network. It must configure any cached routes flushed when OMP peers have lost adjacency.
Which configuration allows the cached OMP routes to be flushed after every 24 hours from its routing table?

A.

B.

C.

D.

Discussion 0

Correct Answer: C Vote an answer

Question #2

Which policy configures an application-aware routing policy under Configuration > Policies?

A. Data policy

B. Control policy

C. Localized policy

D. Centralized policy

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #3

Refer to the exhibit. The network team is implementing a TLOC policy in a network with a hub and spoke layout. The spoke sites must prefer their public-internet circuit for routes advertised by the hub site's WAN Edge with TLOC IP 10.101.1.1. Which configuration achieves this result?

A. apply-policy
site-list Spokes
control-policy TLOC-Policy out

B. apply-policy
site-list Hub
control-policy TLOC-Policy in

C. apply-policy
site-list Spokes
control-policy TLOC-Policy in

D. apply-policy
site-list Hub
control-policy TLOC-Policy out

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #4

An engineer is configuring a data policy for packets that must be captured through the policy.
Which command accomplishes this task?

A. policy > data-policy > vpn-list > sequence > match

B. policy > data-policy > vpn-list > sequence > default-action > accept

C. policy > data-policy > vpn-list > sequence > action

D. policy > data-policy > vpn-list > sequence > default-action > drop

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #5

Which two mechanisms are used by vManage to ensure that the certificate serial number of the WAN Edge router that is needed to authenticate is listed in the WAN Edge Authorized Serial Number list? (Choose two.)

A. Manually upload it to vManage.

B. The vManage is shipped with the list.

C. Synchronize to the PnP.

D. The devices register to vManage directly as the devices come online.

E. Synchronize to the Smart Account.

Discussion 0

Correct Answer: A,E Vote an answer

Question #6

Refer to the exhibit. The users establish a tunnel between branch A and B to communicate directly during video calls. The tunnel must go down after the call is complete. Which two configurations must be applied on the spokes to meet this requirement? (Choose two.)

A. omp
ecmp-limit 16

B. system
on-demand enable

C. omp
send-path-limit 16

D. system
on-demand idle-timeout 10

E. vpn 0
service TE

Discussion 0

Correct Answer: B,D Vote an answer

Question #7

Refer to the exhibit. What binding is created using the tloc-extension command?

A. between ge 0/2.101 of port-type service and ge 0/0 of port-type service

B. between ge 0/2.101 of port-type transport and ge 0/0 of port-type service

C. between ge 0/2.101 of port-type service and ge 0/0 of port-type transport

D. between ge 0/2.101 of port-type transport and ge 0/0 of port-type transport

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #8

What is the next step when the WAN Edge device boots up and resolves the domain in the ZTP process for WAN Edge deployment?

A. The WAN Edge device establishes secure control plane connections with the controllers and secure data plane connections in the SD-WAN overlay network.

B. The WAN Edge device establishes secure connections with the vManage and vSmart and downloads the configuration using NETCONF.

C. The WAN Edge device learns the vBond and organization name from the configuration and initiates a secure control connection to the vBond orchestrator.

D. The WAN Edge router authenticates to the vBond orchestrator with the chassis serial number and root certificate.

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #9

In which device state does the WAN edge router create control connections, but data tunnels are not created?

A. valid

B. staging

C. active

D. backup

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #10

An engineer must configure VRRP for redundancy on WAN Edge router1 running an earlier version than 17.6, considering WAN Edge router2 is configured correctly. Which configuration meets the requirement?

A. Interface GigabitEthernet0/0/1
vrf forwarding 10
ip address 192.168.23.3 255.255.255.0
no ip redirects
ip mtu 1496
vrrp 1 address-family ipv4
timers advertise 1000
priority 150
vrrpv2
address 192.168.23.1 primary
exit-vrrp
arp timeout 1200
end

B. Interface GigabitEthernet0/0/1
vrf forwarding 10
ip address 192.168.23.3 255.255.255.0
no ip redirects
ip mtu 1600
vrrpv2
address 192.168.23.3 primary
exit-vrrp
arp timeout 1200
end

C. Interface GigabitEthernet0/0/1
vrf forwarding 10
ip address 192.168.23.3 255.255.255.0
no ip redirects
ip mtu 1496
vrrp 1 address-family ipv4
timers advertise 500
priority 300
end

D. Interface GigabitEthernet0/0/1
vrf forwarding 10
ip address 192.168.23.3 255.255.255.0
no ip redirects
ip mtu 1600
vrrp 1 address-family ipv4
timers advertise 1000
priority 100
vrrpv2
address 192.168.23.3 primary
exit-vrrp
arp timeout 1200
end

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #11

Refer to the exhibit. The network design team has advised to use private IP addresses and private colors over the SP circuit for the data plane connections. The Public IP should be used for control connections. Which configuration should be applied at SiteA to achieve this task?

A.

B.

C.

D.

Discussion 0

Correct Answer: D Vote an answer

Question #12

Refer to the exhibit. A WAN Edge device was recently added to vManage, but a control connection could not be established. Which action resolves this issue?

A. Install the bootstrap code on WAN Edge and check for CSR.

B. Rectify the Root CA certificate mismatch on WAN Edge devices.

C. Resolve the ZTP reachability and rectify smart account credentials issue.

D. Send the serial number to vBond from the vManage controller.

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #13

What are the default username and password for vSmart Controller when it is installed on a VMware ESXi hypervisor?

A. username admin password admin

B. username admin password cisco

C. username cisco password admin

D. username cisco password cisco

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for Pass4Leader members. You can sign-up / login (it's free).

Question #14

Drag and Drop Question
Drag and drop the REST API calls from the left onto the functions on the right.

Discussion 0

Correct Answer:

Explanation:

Free Cisco 300-415 Practice Test & Real Exam Questions

Download Free Cisco 300-415 Demo