Free CWNP CWNA-106 Practice Test & Real Exam Questions

Exam Code/Number: CWNA-106
Exam Name/Title: Certified Wireless Network Administrator
Certification Provider: CWNP
Corresponding Certification: CWNA Certification

Exam Questions: 140
Updated On: May 31, 2026

Question #1

ABC Company performs government contract work that requires disabling WLANs and has recently purchased an 802.11 Wireless Intrusion Prevention System (WIPS) to enforce their "NO WIRELESS" network security policy.
What attack type cannot be recognized by theWIPS?

A. Packet capturing

B. Deauthentication

C. Rogue APs installation

D. RF jamming

E. Layer 3 DoS

Discussion 0

Correct Answer: A Vote an answer

Question #2

What is an advantage of using WPA2-Personal instead of WEP-128 as a security solution for 802.11 networks?

A. WPA2-Personal is basedon IEEE 802.11 industry standards, but WEP is not.

B. WPA2-Personal uses CCMP for encryption, and WEP-128 uses TKIP for encryption.

C. WPA2-Personal usesdynamic encryption keys, and WEP-128 uses static keys.

D. WPA2-Personal uses 802.1X/EAP for authentication, and WEP-128 uses preshared keys.

Discussion 0

Correct Answer: C Vote an answer

Question #3

The client devices that connect to your network include a mix of dual-band 802.11n and
8 02.11ac, single-band 802.11b/g/n, and some 802.11a/g/n. Your access points are configured with the same SSID on both the 2.4 and 5 GHz bands. The APs are also configured to prioritize client connectivity to 5 GHz.
How does an AP perform band steering to encourage clients to use 5 GHz?

A. The AP may allow an 802.11 association with the client in the 2.4 GHz band, then send unicast channel switch announcements to the client announcing the 5 GHz channel as the new channel.

B. The AP may ignore the initial probe requests or 802.11 authentication requests sent in the 2.4 GHz band by dual-band clients

C. The AP may allow an 802.11 association with the client in the 2.4 GHz band, then the
AP may perform a transparent client handoff by transferring the client's MAC address to the
5 GHz radio.

D. When the client sends a probe request in the 2.4GHz band, the AP may reply with information about the 5 GHz BSS.

Discussion 0

Correct Answer: B Vote an answer

Question #4

When planning an access point deployment that utilizes Power over Ethernet (PoE) switches at the network edge, what design decision could adversely affect the operation of
802.3-2012, Clause 33 APs?

A. The Ethernet switch uplink ports are not connected to an 802.3-2012, Clause 33- compliant core or distribution Ethernet switch.

B. A gigabit Ethernet switch port supporting an 802.11a/g AP auto-negotiates to 100 Mbps.

C. Some APs are connected to a PoE switch and are also receiving power from an AC outlet.

D. All ports on theEthernet switch will be supporting Class 3 PoE powered devices.

Discussion 0

Correct Answer: D Vote an answer

Question #5

ABC Hospital is planning a Wi-Fi infrastructure upgrade wherethe 802.11b/g APs
(HR/DSSS and ERP) would be replaced with new dual-radio 802.11n/802.11ac (HT and
VHT) APs. ABC wants to minimize the time and cost associated with performing a new site survey, so they will be mounting all of the new APs in the same locations and with the same cable drops as the existing APs.
What is one performance drawback with this deployment method?

A. The existing WLAN plan, including the AP locations, may not provide the benefits seen in HT and VHT 802.11 PHY capabilities.

B. Multipath will increase, causing excessive layer-2 retransmissions. The retransmissions will cause latency for VoWiFi handsets.

C. If the existing UTP cabling is not Category 3 or better, the total Ethernet backhaul for each AP will be limited to 100 Mbps.

D. Increased receiver sensitivity on theVHT APs will cause them to continually change channels to avoid co-channel interference.

Discussion 0

Correct Answer: A Vote an answer

Question #6

Prior to association, what parameter can 802.11 client devices measure and use to select the optimal access point for association?

A. Average round trip time to reach the IP router

B. Retry rate of probe request and responseframes

C. Proximity to potential access points

D. Signal strength of access point beacons received

E. Average round trip time to reach the Internet DNS server

Discussion 0

Correct Answer: D Vote an answer

Question #7

What WLAN system feature is required to produce a scenario with the following configuration on a single access point? (Choose 2)
1. SSID = Guest / BSSID = AA:AA:AA:AA:AA:AA /
VLAN = 22 / Subnet = 192.168.22.0 / RF Channel = 6
2. SSID = Corporate / BSSID = BB:BB:BB:BB:BB:BB /
VLAN = 33 / Subnet = 192.168.33.0 / RF Channel = 6 /User Type A
3. SSID = Corporate / BSSID = BB:BB:BB:BB:BB:BB /
VLAN = 44 / Subnet = 192.168.44.0 / RF Channel = 6 / User Type B

A. Virtual Cell with SCA

B. User-based authentication

C. Integrated DHCP server

D. Dual-radio AP hardware

E. Call Admission Control

F. Multiple WLAN Profiles

G. Access Categories

Discussion 0

Correct Answer: B,F Vote an answer

Question #8

You are being interviewed by ABC Company for employment as a wireless site surveyexpert. The interviewing manager asks you what items should be included in a site survey report generated as part of a manual site survey process.
What answer would be accurate?

A. Itemized list of equipment, licenses, and support contracts required forthe facility

B. Documentation noting how each WLAN user group will authenticate to the network

C. RF heat map illustrating coverage and signal quality for each frequency band

D. Documentation proving proper entry of wall material types into the site survey software

Discussion 0

Correct Answer: C Vote an answer

Question #9

For what likely reasons might an organization choose to purchase an AP designed for outdoor deployment to use as an indoor WLAN AP at an industrial facility? (Choose 2)

A. Reduce transient RF interference

B. 802.11 securitycompliance

C. Physical security and theft prevention

D. Protection from environmental conditions

E. Aesthetic requirements

Discussion 0

Correct Answer: C,D Vote an answer

Question #10

In an 802.11 2.4 GHz system, what 22 MHz channels are considered non-overlapping?
(Choose 2)

A. Channels 5 and 10

B. Channels 3 and 7

C. Channels 1 and 5

D. Channels 2 and 8

E. Channels 10 and 13

F. Channels 8 and 11

Discussion 0

Correct Answer: A,D Vote an answer

Download Free CWNP CWNA-106 Demo

Simply submit your e-mail address below to get started with our free demo of your CWNP CWNA-106 exam.